Ididit Column Add-Ons: Shift Indicator with Housing Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Ididit Column Add-Ons: Shift Indicator with Housing herunter. ididit Column Add-Ons: Shift Indicator with Housing User Manual [en] [de] [fr] [it] Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 1
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
PROPERTY OF
ididiT, inc
PROPERTY OF
ididiT, inc
PROPERTY OF
ididiT, inc
PROPERTY OF
ididiT, inc
PROPERTY OF
ididiT, inc
PROPERTY OF
ididiT, inc
ididit inc. 610 S. Maumee St. 49286 Tecumseh, MI PH: 517-424-0577 FAX: 517-424-7293
www.ididitinc.com
Shift Indicator w/Housing Installation Instructions
For 3 Speed, 4 Speed, Ford AOD & AODE & Ford C4 & C6 Shift Indicators w/ Pointer & Housing
For Part Number’s 2600200020, 2600250020, 2600260020, 2600270020, 2600271020, 2600200051, 2600250051,
2600260051, 2600270051, 2600271051, 2600200030, 2600250030, 2600260030, 2600270030, 2600271030,
2600200040, 2600250040, 2600260040, 2600270040, 2600271040
Instruction #: 8000010111 REV 01/13
1. Before you begin your installation, make sure the
column is tilting straight up and down.
2. Measure and mark a line in the upper housing
(sleeve) 3 3/8” down from the top of the column.
(Figure 1)
3. Set the indicator housing on the top of the column
centered from left to right or level on the top of the
column and centered over the line.
4. Use a marker to spot where the holes should be
drilled.
5. Use a center punch before you drill. If using a
center punch on a chrome column be careful not
to hit it too hard because it could pop the chrome.
(Figure 2)
6. Use a .100 or a #38 drill to make the holes. Drill
3/8” deep. (Figure 3)
7. Before installing the housing make sure to clean off
any marks you have made on the column.
8. Slide the Acrylic Indicator in the housing and
install the screws provided in your kit using a #2
Phillips screwdriver. (Figure 4)
9. Next install your pointer. To install the pointer
make sure the column is in Neutral. Block the tires
if the car is on uneven ground.
10. Measure from the top of the shift hub down 3/8”
and behind the “N” on the indicator, put a mark.
This is going to be the front edge of the pointer.
(Figure 5)
11. Cleantheareatoremoveanyoilorngerprints.
Remove the red tape backer on the pointer and
stick the pointer on the column with the big end
even with the mark on the shift hub and centered
with “N” on the indicator. (Figure 6)
12. Your installation is now complete. (Figure 7)
Seitenansicht 0
1

Inhaltsverzeichnis

Seite 1 - REV 01/13

PROPERTY OFididiT, incPROPERTY OFididiT, incPROPERTY OFididiT, incPROPERTY OFididiT, incPROPERTY OFididiT, incPROPERTY OFididiT, incididit inc. 610 S

Kommentare zu diesen Handbüchern

Keine Kommentare